CLEVELAND SRIXON Cleveland Launcher XL Driver Lite – Draw Face

XL HEAD DESIGN

This is huge: a bigger head means an MOI of 5,200 g-cm2 our most ever in a Cleveland Golf driver. Add that forgiveness to a high launch from low-and-deep weighting, and youll enjoy maximum distance with maximum fun.

REBOUND FRAME

Whats better than one flex zone? Two (duh). Alternating zones of flexibility and rigidity direct more energy into the golf ball for increased ball speed and distance on every shot.

ACTION MASS CB

An 8g weight placed inside the end of the grip delivers better balance for more control without extra effort.

ADJUSTABLE HOSEL

Adjust your loft from 9 to 12 degrees to optimize your launch angle, distance, and shot shape. Loft can be adjusted at 0.5 deg increments with 12 positions in all.

ACCURACY BUILD

If precision is your top priority, this custom configuration is an inch shorter without counterbalancing for max control off the tee.

LAUNCHER XL DRIVER SPECS

LOFT	HEAD SIZE	LIE ANGLE	STANDARD BUILD LENGTH	STANDARD BUILD SW	ACCURACY BUILD LENGTH*	ACCURACY BUILD SW*	HAND
9	460cc	58.5	45.75″	D3	44.75″	D0	RH/LH
10.5	460cc	60.0	45.75″	D3	44.75″	D0	RH/LH
12	460cc	58.5	45.75″	D3	44.75″	D0	RH/LH

*Accuracy build is a featured, preconfigured custom option for players who seek maximum control. Head/shaft/grip are the same, but length is 1 shorter and 8g grip weight is excluded.

PROJECT X CYPHER 50 SHAFT

TIP DIAMETER	WEIGHT (g)	LAUNCH	SPIN	FLEX
0.335″	52(A), 54(R), 56(S)	Mid-High	Mid-High	5.0-A, 5.5-R, 6.0-S

GOLF PRIDE TOUR VELVET 360

INSIDE DIAMETER	WEIGHT (g)
58 ROUND	52 g

12 DRIVERS IN 1?

HOSEL SLEEVE ADJUSTABILITY GUIDE

The Launcher XL Driver comes standard with an adjustable hosel sleeve that adjusts from 9.0 to 12.0 in 0.5 increments. In all, theres 12 different positions which means youre bound to find the perfect setup for your swing.

The 4 primary loft settings are marked on the sleeve at 9.0, 10.5, 12.0 and 10.5 Flat. The varying settings between each are visible on the pre-installed shaft tip.

BALL LAUNCHING TOO LOW?

INCREASE LOFT UP TO 12 DEGREES.

BALL LAUNCHING TOO HIGH?

LOWER LOFT DOWN TO 9 DEGREES.

Adjusting the drivers loft also has a slight impact on your face and lie angles. The chart below will help you decide which configuration is right for your swing. Side note: its also a great conversation starter next time youre trying to impress your father-in-law.

UNIVERSAL TORX 25 WRENCH

USE ONLY THE CUSTOM TORQUE WRENCH WHEN MAKING HOSEL ADJUSTMENTS.

HOW TO REMOVE AND INSTALL QTS SLEEVE (TORQUE WRENCH OPERATION)

3. Loosen

With the torque wrench aligned with the shaft, turn it counterclockwise.

*Shaft will come off without loosening the screw too much.

4. Tighten

With the torque wrench aligned with the shaft, turn it counterclockwise.

*Always tighten until you hear a ‘click’. Failure to do so may result in separation of the club head or product damage.

5. Insert the shaft into the head

6. QTS setting examples

Be sure to read the Important Precautions carefully and exercise appropriate care. The manufacturer assumes no liability for injury or product damage due to failure to comply with the instructions herein.

RULES OF GOLF

It is against the rules to modify club performance during a round by changing the QTS sleeve position or exchanging weights to change the CG position, as this breaches the Rules of Golf regulation 4-2a, which states: «During a stipulated round, the playing characteristics of a club must not be purposely changed by adjustment or by any other means.»

BEFORE USING

Check to see that the QTS sleeve is properly secured.

Tighten until you hear a ‘click’. If you fail to properly secure the sleeve, there is a possibility that the head may come off mid swing, injuring either you or a bystander.